Power control for special heating elements

When standard control is not enough

Not all heating elements behave like a simple resistive element with stable resistance. Some materials change resistance significantly with temperature or respond extremely quickly to applied power. This includes MoSi₂ (molybdenum disilicide), SiC (silicon carbide) and SWIR (short-wave infrared).
If these elements are not controlled correctly, it can lead to short service life, unstable operation or, in the worst case, damage to the equipment. Therefore, they require advanced power control with functions such as ramp times, soft start and precise regulation.

MoSi₂ – molybdenum disilicide

MoSi₂ elements can deliver very high temperatures—up to around 1800 °C—and are often used in laboratory and process furnaces where high heat resistance is required.
A particular challenge is the strongly temperature-dependent resistance. When the element is cold, the resistance is low, and the start-up current can therefore become extremely high—almost like a short circuit. Without correct control, the element can burn out or the fuse can melt within seconds.
Soft start and ramp times are therefore crucial. By gradually increasing the power until the element reaches operating temperature, shock loading is avoided. Modern power controllers can be programmed to deliver a controlled rise in current, so the MoSi₂ element heats up safely and stably.

SiC – silicon carbide

SiC elements are also used in high-temperature and process furnaces. Their resistance changes both with temperature and with age.
When a SiC element is new, the resistance is low at cold start, which requires soft start to avoid high inrush currents.
With load diagnostics, you can monitor the element’s impedance and detect changes in resistance. This enables planned replacement before the element fails—an example of how intelligent control can support predictive maintenance and minimise unplanned downtime.

SWIR – short-wave infrared

SWIR elements differ significantly from MoSi₂ and SiC. They have low mass and can therefore heat up extremely quickly. This makes them ideal for applications where fast response is required—for example in drying and curing processes in the food industry, electronics manufacturing or materials processing.
The challenge is that SWIR elements respond so quickly that even small fluctuations in power can cause large temperature changes. Without precise control, this can lead to overshoot, uneven heat distribution or premature ageing of the element.
Here, phase-angle control is often the most suitable method. By regulating the power in real time with high resolution, you can ensure a stable temperature, even when process requirements change quickly.

Controller functions that make the difference

Although MoSi₂, SiC and SWIR are very different materials, there are some common denominators when it comes to power control.

  • Ramp times and soft start: Necessary for MoSi₂ and SiC, but also useful for other elements, as it reduces the load on the heating element and the installation.
  • Different firing modes: Burst, half-cycle or phase-angle depending on the element’s characteristics and process requirements.
  • Load diagnostics: Monitoring resistance and impedance so changes are detected early.
  • Communication: Integration with PLC and SCADA so data and alarms are displayed directly in the control system.
  • Alarms and safety: Differentiation of faults so you can quickly see whether the problem is due to the load, the mains supply or the installation.

These functions are part of what distinguishes a modern SCR power controller from a simple power regulator.

Examples from practice

In a research furnace with MoSi₂ elements, soft start can be the difference between an element that lasts for years and one that burns out in a few minutes.
In a process furnace with SiC elements, load diagnostics can reveal increasing resistance so replacement can be planned for the next service.
In the food industry, SWIR elements are used for rapid drying of products. Here, precise phase-angle control is crucial for uniform heat distribution and high product quality.

Future control of special elements

As energy requirements tighten and processes become more complex, elements such as MoSi₂, SiC and SWIR are expected to become even more widespread. This places correspondingly greater demands on control.
In the future, data collection and integration with energy management systems will enable the combination of precise power control and flexible energy consumption. Even the most demanding heating elements can thus become an active part of the green transition.

Specialised control provides longer service life

Special heating elements require specialised control. MoSi₂ and SiC must be started softly to avoid damage during cold start, while SWIR requires extreme precision to take advantage of its fast response.
With the right power controllers, you can protect the elements, extend service life and ensure a more stable process that is ready for future requirements.

Contact us

Are you working with special heating elements such as MoSi₂, SiC or SWIR?
Contact us—we will help you choose the right control solution and optimise your process.

Call us on +45 7669 7090 or email info@newtronic.dk.
Our specialists are ready to advise you on the optimal solution for your specific application.

Want to know more?

Electric tubular heater during heating and testing